Document Number: 2151 Date Update: 13/3/96 Pages: 10The document is available in the following formats:
Portable Document Format 123K and Raw Text Format 12K (for text retrieval only)
The document is also available compressed with PKZIP® in the following formats:
Portable Document Format 79K, PrinterLeaf 65K and PostScript 102K
WIDE BANDWIDTH QUAD J-FET OPERATIONAL AMPLIFIERS . LOW POWER CONSUMPTION . WIDE COMMON-MODE (UP TO V CC + ) AND DIFFERENTIAL VOLTAGE RANGE . LOW INPUT BIAS AND OFFSET CURRENT . OUTPUT SHORT-CIRCUIT PROTECTION . HIGH INPUT IMPEDANCE J-FET INPUT STAGE . INTERNAL FREQUENCY COMPENSATION . LATCH UP FREE OPERATION . HIGH SLEW RATE : 16V/ m s (typ) N DIP14 (Plastic Package) Inverting Input 2 Non-inverting Input 2 Non-inverting Input 1 CC V - CC V 1 2 3 4 8 5 6 7 9 10 11 12 13 14 + Output 3 Output 4 Non-inverting Input 4 Inverting Input 4 Non-inverting Input 3 Inverting Input 3 - + - + - + - + Output 1 Inverting Input 1 Output 2 PIN CONNECTIONS (top view) DESCRIPTION These circuits are high speed J-FET input quad opera- tional amplifiers incorporating well matched, high voltage J-FET and bipolar transistors in a monolithic integrated circuit. The devices feature high slew rates, low input bias and offset currents, and low offset voltage temperature coefficient. D SO14 (Plastic Micropackage) LF147 - LF247 LF347 February 1996 ORDER CODES Part Number Temperature Package N D LF347 0 o C, +70 o C w w LF247 -40 o C, +105 o C w w LF147 -55 o C, +125 o C w w 1/10 ABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit V CC Supply Voltage - (note 1) + 18 V V i Input Voltage - (note 3) + 15 V V id Differential Input Voltage - (note 2) + 30 V P tot Power Dissipation 680 mW Output Short-circuit Duration - (note 4) Infinite T oper Operating Free Air Temperature Range LF347 LF247 LF147 0 to 70 -40 to 105 -55 to 125 o C T stg Storage Temperature Range -65 to 150 o C Notes : 1. All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the supply voltages where the zero reference level is the midpoint between V CC + and V CC - . 2. Differential voltages are at the non-inverting input terminal with respect to the inverting input terminal. 3. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is less. 4. The output may be shorted to ground or to either supply. Temperature and /or supply voltages must be limited to ensure that the dissipation rating is not exceeded. Output Non-inverting input Inverting input V CC V CC 200 W W 10 0 W 10 0 1.3k 30k 35k 35k W 10 0 1.3k 8.2k SCHEMATIC DIAGRAM (each amplifier) LF147 - LF247 - LF347 2/10 ELECTRICAL CHARACTERISTICS V CC = + 15V, T amb = 25 o C (unless otherwise specified) Symbol Parameter LF147 - LF247 LF347 Unit Min. Typ. Max. V io Input Offset Voltage (R S = 10k W ) T amb = 25 o C T min. 3 T amb 3 T max. 3 10 13 mV DV io Input Offset Voltage Drift 10 m V/ o C I io Input Offset Current * T amb = 25 o C T min. 3 T amb 3 T max. 5 100 4 pA nA I ib Input Bias Current * T amb = 25 o C T min. 3 T amb 3 T max. 20 200 20 pA nA A vd Large Signal Voltage Gain (R L = 2k W , V O = + 10V) T amb = 25 o C T min. 3 T amb 3 T max. 50 25 200 V/mV SVR Supply Voltage Rejection Ratio (R S = 10k W ) T amb = 25 o C T min. 3 T amb 3 T max. 80 80 86 dB I CC Supply Current, per Amp, no Load T amb = 25 o C T min. 3 T amb 3 T max. 1.4 2.7 2.7 mA V icm Input Common Mode Voltage Range + 11 +15 -12 V CMR Common Mode Rejection Ratio (R S = 10k W ) T amb = 25 o C T min. 3 T amb 3 T max. 70 70 86 dB Ios Output Short-circuit Current T amb = 25 o C T min. 3 T amb 3 T max. 10 10 40 60 60 mA + V OPP Output Voltage Swing T amb = 25 o C R L = 2k W R L = 10k W T min. 3 T amb 3 T max. R L = 2k W R L = 10k W 10 12 10 12 12 13.5 V SR Slew Rate (V i = 10V, R L = 2k W, C L = 100pF, T amb = 25 o C, unity gain) 12 16 V/ m s t r Rise Time (V i = 20mV, R L = 2k W , C L = 100pF, T amb = 25 o C, unity gain) 0.1 m s K OV Overshoot (V i = 20mV, R L = 2k W , C L = 100pF, T amb = 25 o C, unity gain) 10 % GBP Gain Bandwidth Product (f = 100kHz, T amb = 25 o C, V in = 10mV, R L = 2k W , C L = 100pF) 2.5 4 MHz R i Input Resistance 10 12 W THD Total Harmonic Distortion (f = 1kHz, A V = 20dB, R L = 2k W , C L = 100pF, T amb = 25 o C, V O = 2V PP ) 0.01 % e n Equivalent Input Noise Voltage (f = 1kHz, R s = 100 W ) 15 nV / ``` Hz j m Phase Margin 45 Degrees V O1 /V O2 Channel Separation (A v = 100, T amb = 25 o C) 120 dB * The input bias currents are junction leakage currents which approximately double for every 10 o C increase in the junction temperature. LF147 - LF247 - LF347 3/10 30 20 25 15 10 5 0 MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE (V) 100 1K 10K 100K 10M 1M FREQUENCY (Hz) See Figure 2 = 2k W R L = +255C T a m b = 15V V CC = 5V V CC = 10V V CC MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS FREQUENCY 30 20 25 15 10 5 0 MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE (V) 100 1K 10K 100K 10M 1M FREQUENCY (Hz) See Figure 2 = +25 C T amb = 10k W R L V CC = 10V V CC = 15V V CC = 5V MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS FREQUENCY 30 25 20 15 10 5 0 MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE (V) FREQUENCY (Hz) 10k 40k 100k 400k 1M 4M 10M T amb = +25 C T amb = -55 C T amb = +125 C R L = 2k W See Figure 2 V CC = 15V MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS FREQUENCY 3 0 2 5 2 0 1 0 5 1 5 0 -75 -25 2 5 7 5 125 -50 0 5 0 -50 MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE (V) TEMPERATURE (5C) V C C = 15V See Figure 2 R L = 10k W R L = 2k W MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS FREE AIR TEMP. 30 25 20 15 10 5 0 MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE (V) 0.1 0.2 0.4 0.7 1 2 4 7 10 LOAD RESISTANCE ( k W ) T amb = +255C V CC = 15V See Figure 2 MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS LOAD RESISTANCE 30 25 20 15 10 5 0 2 4 6 8 10 12 14 16 MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE (V) SUPPLY VOLTAGE (V) R L = 10 k W T amb = +255C MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE VERSUS SUPPLY VOLTAGE LF147 - LF247 - LF347 4/10 100 10 1 0.1 0.01 INPUT BIAS CURRENT (nA) -50 -25 0 25 50 75 100 125 TEMPERATURE (5C) V CC = 15V INPUT BIAS CURRENT VERSUS FREE AIR TEMPERATURE 1000 400 200 100 20 40 10 4 2 1 DIFFERENTIAL VOLTAGE AMPLIFICATION (V/V) -75 -50 -25 0 25 50 75 100 125 TEMPERATURE (5C) R L = 2k W V O = 10V V CC = 15V LARGE SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION VERSUS FREE AIR TEMPERATURE FREQUENCY (Hz) DIFFERENTIAL VOLTAGE AMPLIFICATION (V/V) 100 10 100 1K 10K 100K 10M 1M 1 DIFFERENTIAL VOLTAGE AMPLIFICATION (left scale) 180 90 0 R = 2k W C = 100pF V = 15V T = +125 C L L CC amb PHASE SHIFT (right scale) LARGE SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE SHIFT VERSUS FREQUENCY 250 225 200 175 150 125 100 75 50 25 0 TOTAL POWER DISSIPATION (mW) -75 -50 -25 0 25 50 75 100 125 TEMPERATURE (5C) V CC = 15V No signal No load TOTAL POWER DISSIPATION VERSUS FREE AIR TEMPERATURE 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 SUPPLY CURRENT (mA) -75 -50 -25 0 25 50 75 100 125 TEMPERATURE (5C) V CC = 15V No signal No load SUPPLY CURRENT PER AMPLIFIER VERSUS FREE AIR TEMPERATURE 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 SUPPLY CURRENT (mA) 0 2 4 6 8 10 12 14 16 SUPPLY VOLTAGE (V) No signal No load = +255C T a m b SUPPLY CURRENT PER AMPLIFIER VERSUS SUPPLY VOLTAGE LF147 - LF247 - LF347 5/10 89 88 87 86 85 84 -50 -25 0 25 50 75 100 125 COMMON MODE MODE REJECTION RATIO (dB) TEMPERATURE (5C) 83 -75 R L = 10 k W = 15V V C C COMMON MODE REJECTION RATIO VERSUS FREE AIR TEMPERATURE 6 4 2 0 -2 -4 0 0.5 1 1.5 2 2.5 3 3.5 INPUT AND OUTPUT VOLTAGES (V) TIME ( m s) -6 = 15V V CC R L = 2 k W = 100pF C L T amb = +25 C OUTPUT INPUT VOLTAGE FOLLOWER LARGE SIGNAL PULSE RESPONSE t r 28 24 20 16 12 8 4 0 -4 OUTPUT VOLTAGE (mV) 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 TIME ( m s) 10% 90% OVERSHOOT R L = 2k W T amb = +255C V CC = 15V OUTPUT VOLTAGE VERSUS ELAPSED TIME 70 60 50 40 30 20 10 0 EQUIVALENT INPUT NOISE VOLTAGE (nV/VHz) 10 40 100 400 1k 4k 10k 40k 100k FREQUENCY (Hz) A V = 10 R S = 100 W T amb = +255C V CC = 15V EQUIVALENT INPUT NOISE VOLTAGE VERSUS FREQUENCY 1 0.4 0.1 0.04 0.01 0.004 0.001 TOTAL HARMONIC DISTORTION (%) 100 400 1k 4k 10k 40k 100k FREQUENCY (Hz) A V = 1 T amb = +255C V CC = 15V = 6V V O (rms) A V = 1 T amb = +255C = 6V V O (rms) V CC = 15V TOTAL HARMONIC DISTORTION VERSUS FREQUENCY LF147 - LF247 - LF347 6/10 - e I LF347 1/4 e o C L = 100pF R = 2k W L Figure 1 : Voltage Follower PARAMETER MEASUREMENT INFORMATION - e I LF347 R L 1/4 C L = 100pF 1k W 10k W e o Figure 2 : Gain-of-10 Inverting Amplifier - L F 3 4 7 1/4 - - - L F 3 4 7 1/4 LF3 4 7 1/4 L F 3 4 7 1/4 1 M W 1 m F Output A Outp ut B Outp ut C I np ut 1 0 0 k W 1 0 0 k W 1 0 0 k W 1 0 0 k W 1 O O m F V C C + f = 100kHz O TYPICAL APPLICATIONS AUDIO DISTRIBUTION AMPLIFIER LF147 - LF247 - LF347 7/10 - - LF347 1/4 220pF 43k W Input 1.5k W 43k W 220pF 43k W 16k W LF347 1/4 30k W Output A - LF347 1/4 1.5k W 220pF 43k W 220pF 43k W - LF347 1/4 43k W 16k W 30k W Output B Ground TYPICAL APPLICATIONS (continued) POSITIVE FEEDBACK BANDPASS FILTER CASCADED BANDPASS FILTER fo = 100kHz ; Q = 69 ; Gain = 16 OUTPUT B SECOND ORDER BANDPASS FILTER fo = 100kHz ; Q = 30 ; Gain = 4 OUTPUT A LF147 - LF247 - LF347 8/10 PACKAGE MECHANICAL DATA 14 PINS - PLASTIC DIP Dimensions Millimeters Inches Min. Typ. Max. Min. Typ. Max. a1 0.51 0.020 B 1.39 1.65 0.055 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 15.24 0.600 F 7.1 0.280 i 5.1 0.201 L 3.3 0.130 Z 1.27 2.54 0.050 0.100 LF147 - LF247 - LF347 9/10 PACKAGE MECHANICAL DATA 14 PINS - PLASTIC MICROPACKAGE (SO) Dimensions Millimeters Inches Min. Typ. Max. Min. Typ. Max. A 1.75 0.069 a1 0.1 0.2 0.004 0.008 a2 1.6 0.063 b 0.35 0.46 0.014 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.020 c1 45 o (typ.) D 8.55 8.75 0.336 0.334 E 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 7.62 0.300 F 3.8 4.0 0.150 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.020 0.050 M 0.68 0.027 S 8 o (max.) Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsi- bility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No licence is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of SGS-THOMSON Microelectronics. { 1996 SGS-THOMSON Microelectronics - All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. LF147 - LF247 - LF347 10/10